收藏本站
71M6545/71M6545H Data Sheet
1Wh/pulse, a power applied to the meter of 120 V and 30 A results in one pulse per second. If the load is
240 V at 150 A, ten pulses per second are generated.
Control is transferred to the MPU for pulse generation if EXT_PULSE = 1 (CE RAM 0x20[5]). In this case,
the pulse rate is determined by APULSEW and APULSER (CE RAM 0x44 and 0x48) . The MPU has to load
the source for pulse generation in APULSEW and APULSER to generate pulses. Irrespective of the
EXT_PULSE status, the output pulse rate controlled by APULSEW and APULSER is implemented by the CE
only. By setting EXT_PULSE = 1, the MPU is providing the source for pulse generation. If EXT_PULSE is 0,
W0SUM_X and VAR0SUM_X are the default pulse generation sources. In this case, creep cannot be
controlled since it is an MPU function.
The maximum pulse rate is 3*F S = 7.5 kHz.
See 2.3.6.2 VPULSE and WPULSE (page 27 ) for details on how to adjust the timing of the output pulses.
The maximum time jitter is 1/6 of the multiplexer cycle period (nominally 67 μs) and is independent of the
number of pulses measured. Thus, if the pulse generator is monitored for one second, the peak jitter is
67 ppm. After 10 seconds, the peak jitter is 6.7 ppm. The average jitter is always zero. If it is attempted
to drive either pulse generator faster than its maximum rate, it simply outputs at its maximum rate without
exhibiting any rollover characteristics. The actual pulse rate, using WSUM as an example, is:
RATE =
WRATE ? WSUM ? F S ? X
2 46
Hz ,
where F S = sampling frequency (2184.53 Hz), X = Pulse speed factor derived from the CE variables
PULSE_SLOW (CE RAM 0x20[0]) and PULSE_FAST (CE RAM 0x20[1]) .
Table 75: CE Pulse Generation Parameters
CE
Address
0x21
0x22
0x23
0x45
0x46
0x47
0x48
0x49
0x4A
0x4B
0x4C
108
Name
WRATE
KVAR
SUM_PRE
APULSEW
WPULSE_CTR
WPULSE_ FRAC
WSUM_ ACCUM
APULSER
VPULSE_CTR
VPULSE_ FRAC
VSUM_ACCUM
Default
227
6444
2184
0
0
0
0
0
0
0
0
Description
Kh = VMAX*IMAX*K / ( WRATE *N ACC *X) Wh/pulse
where:
K = 76.3594 when used with local sensors (CT or shunt)
K = 54.5793 when used with 71M6xx3 remote sensors
Scale factor for VAR measurement.
Number of samples per accumulation interval, as specified in
SUM_SAMPS[12:0], I/O RAM 0x2107[4:0], 0x2108[7:0] (N ACC ).
Wh pulse (WPULSE) generator input to be updated by the MPU
when using external pulse generation. The output pulse rate is:
APULSEW * F S * 2 -32 * WRATE * X * 2 -14 .
This input is buffered and can be updated by the MPU during a
conversion interval. The change takes effect at the beginning of
the next interval.
Counter for WPULSE output.
Unsigned numerator, containing a fraction of a pulse. The value
in this register always counts up towards the next pulse.
Roll-over accumulator for WPULSE.
VARh (VPULSE) pulse generator input.
Counter for VPULSE output.
Unsigned numerator, containing a fraction of a pulse. The value
in this register always counts up towards the next pulse.
Roll-over accumulator for VPULSE.
v2
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
720-10007-00300 CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025 CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300 CBL DSUB 9PIN FML-9PIN MALE 3M
720-10021-00300 CBL DSUB 9PIN FML-9PIN FEMAL 3M
72231-0881 8 POS T/P SHLD 4 GR ASSY
7250B PANEL KIT BOTTOM FOR R-1220 CASE
731-10061-00200 CBL DSUB HD 15FEMAL-15MALE 2.0M
73304-111 MJ HOR ESMT 8/8 H/O T&R
相关代理商/技术参数
71M6545-IGTR/F 功能描述:计量片上系统 - SoC Metrology Proc. (3P 64K Flsh .1%) RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6545T-IGT/F 制造商:Maxim Integrated Products 功能描述:METROLOGY PROCESSORS - Rail/Tube
71M6545T-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE AFE, 32KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6601 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IF 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IL 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IL/F 功能描述:模数转换器 - ADC Isolated Sensor IC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
71M6601-ILF 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring